Claron Polyseal Single Acting Rod Seal CP

Get a quote

Design:

CLARON STYLE CP is designed with a symmetrical profile for use as a single acting rod or piston seal. The seal is a precision moulded Nitrile rubber sealing element with a fabric reinforced base to resist extrusion. Designed with initial radial interference to effect low pressure sealing, at higher pressures the seal is energised thus increasing the sealing force. Rubberised fabric has the advantage of retaining the sealing media within it’s surface, thus reducing friction and wear. Style CP is produced with radial grooves incorporated into the top of the seal on the pressure side. This innovative design ensures a rapid energisation of the seal without excessive end float and resultant wear.

 

These range perameters are Maximum simultaneous conditions.

Optimum service conditions are affected by temperature, speed, pressure, surface finish and extrusion gaps.

Refer to Appendix 1 for further information.

NBR Rubber
DIN Hydraulic Fluid Description °C
H Mineral oil without additives 100
H-L Mineral Fluid with anti corrosion and anti ageing additives 100
H-LP Mineral oil as HL plus additives reducing wear, raising load 100
H-LPD Mineral oil as H-LP but with detergents and dispersants 100
H-V Mineral oil as H-LP plus improved viscosity temp. 100
HFA E Emulsions of mineral oil in water. Water content 80-95% 55
HFA S Synthetic oil in water. Water content 80-95% 55
HFB Emulsions of water in mineral oil. Water content 40% 60
HFC Aqueous polymer solutions. Water content 35% 60
HFD R Phosphoric acid ester based NS
HFD S Chlorinated hydrocarbon based NS
HFD T Mixtures of HFD R and HFD S NS
HEPG Polyglycol based NS
HETG Vegetable Oil based 60
HEES Fully synthetic ester based NS

Note: Clearance gap F is the maximum permissable. i.e. gap completely on one side, in the temperature range of -30°C to 100°C The use of a suitably selected Claron bearing ring will effectively reduce the clearance gap F max. to a value closer to F/2 thus increasing the pressure capability of the seal.

 

Housing:

For surface finish and recommended lead in chamfers refer to the illustration below. For housing dimensions and machining tolerances refer to the catalogue page of selected seal. Refer to appendix 4 for value of tolerance symbols. For Piston applications refer to section B.

Fitting:

For the seal to function correctly, it is important that care be taken in fitting the seal within its housing. For a detailed checklist, refer to Appendix 3.

Part Number Js 11 f8               H9                 L1 Nominal
ØD1 Ød1                 ØG +0.25
-0.00
Sec S Min
C
Max
R1
CP 078047 20,00 12,00 6,30 4,00 2,00 0,20
CP 094063/1 24,00 16,00 7,50 4,00 2,00 0,20
CP 094063/2 24,00 16,00 6,30 4,00 2,00 0,20
CP 098047 25,00 12,00 10,00 6,50 2,50 0,40
CP 098070 25,00 18,00 7,00 3,50 2,00 0,20
CP 102062/1 26,00 16,00 8,00 5,00 2,50 0,40
CP 102066 26,00 17,00 5,70 4,50 2,00 0,20
CP 102070 26,00 18,00 6,30 4,00 2,00 0,20
CP 102078 26,00 20,00 5,50 3,00 1,50 0,20
CP 106059 27,00 15,00 7,00 6,00 2,50 0,40
CP 110070 28,00 18,00 6,30 5,00 2,50 0,40
CP 110078 28,00 20,00 7,00 4,00 2,00 0,20
CP 110078/1 28,00 20,00 6,30 4,00 2,00 0,20
CP 114074 29,00 19,00 8,00 5,00 2,50 0,40
CP 118078/1 30,00 20,00 8,00 5,00 2,50 0,40
CP 118086/1 30,00 22,00 6,30 4,00 2,00 0,20
CP 118086/2 30,00 22,00 7,50 4,00 2,00 0,20
CP 125086 32,00 22,00 7,50 5,00 2,50 0,40
CP 125094 32,00 24,00 7,00 4,00 2,00 0,20
CP 129098/1 33,00 25,00 6,30 4,00 2,00 0,20
CP 137098 35,00 25,00 8,00 5,00 2,50 0,40
CP 141110/1 36,00 28,00 6,40 4,00 2,00 0,20
CP 149110/1 38,00 28,00 8,00 5,00 2,50 0,40
CP 149118 38,00 30,00 6,40 4,00 2,00 0,20
CP 149118/1 38,00 30,00 8,50 4,00 2,00 0,20
CP 157118 40,00 30,00 7,50 5,00 2,50 0,40
CP 157125/1 40,00 32,00 6,40 4,00 2,00 0,20
CP 165125 42,00 32,00 8,00 5,00 2,50 0,40
CP 169137 43,00 35,00 6,40 4,00 2,00 0,20
CP 173141 44,00 36,00 6,40 4,00 2,00 0,20
CP 173141/1 44,00 36,00 8,50 4,00 2,00 0,20
CP 177118/1 45,00 30,00 9,00 7,50 4,00 0,80
CP 177137/1 45,00 35,00 9,00 5,00 2,50 0,40
CP 177137/5 45,00 35,00 8,00 5,00 2,50 0,40
CP 181141/1 46,00 36,00 8,00 5,00 2,50 0,40
CP 181149 46,00 38,00 6,30 4,00 2,00 0,20
CP 185125 47,00 32,00 11,00 7,50 4,00 0,80
CP 188157 48,00 40,00 6,40 4,00 2,00 0,20
CP 196137/1 50,00 35,00 12,50 7,50 4,00 0,80
CP 196137/2 50,00 35,00 11,00 7,50 4,00 0,80
CP 196157 50,00 40,00 11,00 5,00 2,50 0,40
CP 196157/2 50,00 40,00 13,50 5,00 2,50 0,40
CP 196157/3 50,00 40,00 7,50 5,00 2,50 0,40
CP 196165 50,00 42,00 6,30 4,00 2,00 0,20
CP 200141 51,00 36,00 11,50 7,50 4,00 0,80
Js 11 f8 H9 +0,25 Nominal Min Max
0,00
ØD1 Ød1 ØG L1 S C R1
CP 216157/2 55,00 40,00 11,50 7,50 4,00 0,80
CP 216177 55,00 45,00 8,00 5,00 2,50 0,40
CP 216177/3 55,00 45,00 10,50 5,00 2,50 0,40
CP 228196 58,00 50,00 8,50 4,00 2,00 0,20
CP 236177/1 60,00 45,00 11,50 7,50 4,00 0,80
CP 236196 60,00 50,00 8,00 5,00 2,50 0,40
CP 236196/3 60,00 50,00 14,50 5,00 2,50 0,40
CP 244196/1 62,00 50,00 9,50 6,00 3,00 0,40
CP 248188/2 63,00 48,00 11,00 7,50 4,00 0,80
CP 255196/1 65,00 50,00 11,00 7,50 4,00 0,80
CP 255216 65,00 55,00 10,50 5,00 2,50 0,40
CP 255216/1 65,00 55,00 8,00 5,00 2,50 0,40
CP 259220 66,00 56,00 8,00 5,00 2,50 0,40
CP 275196 70,00 50,00 14,50 10,00 5,00 0,80
CP 275236/3 70,00 60,00 8,00 5,00 2,50 0,40
CP 275236/4 70,00 60,00 14,50 5,00 2,50 0,40
CP 279220 71,00 56,00 12,50 7,50 4,00 0,80
CP 283236 72,00 60,00 10,0 6,00 3,00 0,40
CP 283236/2 72,00 60,00 11,00 6,00 3,00 0,40
CP 295248 75,00 63,00 9,60 6,00 3,00 0,40
CP 303255 77,00 65,00 9,60 6,00 3,00 0,40
CP 307248 78,00 63,00 12,50 7,50 4,00 0,80
CP 314236 80,00 60,00 14,50 10,00 5,00 0,80
CP 314255 80,00 65,00 11,50 7,50 4,00 0,80
CP 314275/1 80,00 70,00 8,00 5,00 2,50 0,40
CP 314275/3 80,00 70,00 12,00 5,00 2,50 0,40
CP 322275/1 82,00 70,00 9,60 6,00 3,00 0,40
CP 322275/2 82,00 70,00 11,00 6,00 3,00 0,40
CP 334255 85,00 65,00 14,50 10,00 5,00 0,80
CP 334275 85,00 70,00 12,50 7,50 4,00 0,80
CP 334295/1 85,00 75,00 8,00 5,00 2,50 0,40
CP 342295 87,00 75,00 9,50 6,00 3,00 0,40
CP 354275/1 90,00 70,00 10,50 10,00 5,00 0,80
CP 358318 91,00 81,00 8,00 5,00 2,50 0,40
CP 362314 92,00 80,00 9,60 6,00 3,00 0,40
CP 362314/1 92,00 80,00 11,00 6,00 3,00 0,40
CP 374295 95,00 75,00 14,50 10,00 5,00 0,80
CP 374314 95,00 80,00 13,00 7,50 4,00 0,80
CP 374314/1 95,00 80,00 12,50 7,50 4,00 0,80
CP 374334 95,00 85,00 8,00 5,00 2,50 0,40
CP 393314 100,00 80,00 14,50 10,00 5,00 0,80
CP 393334 100,00 85,00 12,50 7,50 4,00 0,80
CP 393354 100,00 90,00 10,50 5,00 2,50 0,40
CP 401354 102,00 90,00 9,60 6,00 3,00 0,40
CP 413334/1 105,00 85,00 13,00 10,00 5,00 0,80

 

CP 413354 105.00 90.00 9.50 7.50 4.00 0.80
CP 413354/1 105.00 90.00 12.50 7.50 4.00 0.80
CP 421374 107.00 95.00 12.50 6.00 3.00 0.40
CP 433342 110.00 87.00 8.00 11.50 5.00 0.80
CP 433342/1 110.00 87.00 18.50 11.50 5.00 0.80
CP 452393/1 115.00 100.00 12.00 7.50 4.00 0.80
CP 452413 115.00 105.00 11.00 5.00 2.50 0.40
CP 472393 120.00 100.00 14.50 10.00 5.00 0.80
CP 492433 125.00 110.00 12.00 7.50 4.00 0.80
CP 492452 125.00 115.00 8.00 5.00 2.50 0.40
CP 523484 133.00 123.00 8.00 5.00 2.50 0.40
CP 590492 150.00 125.00 14.50 12.50 6.50 1.20
CP 629551/2 160.00 140.00 12.00 10.00 5.00 0.80
CP 661602 168.00 153.00 12.50 7.50 4.00 0.80
CP 669590/1 170.00 150.00 14.50 10.00 5.00 0.80

Merk

Claron Polyseals

Beoordelingen

Er zijn nog geen beoordelingen.

Wees de eerste om “Claron Polyseal Single Acting Rod Seal CP” te beoordelen

Het e-mailadres wordt niet gepubliceerd. Vereiste velden zijn gemarkeerd met *

WE’D LOVE TO HELP

Get a qoute