Claron Polyseal Single Acting Rod Seal CPI

Get a quote

Design:

Claron Style CPI is designed for use as a single acting rod seal. The seal is a precision moulded Nitrile rubber sealing element with a fabric reinforced base and an acetal back up ring to resist extrusion. The acetal back up ring allows larger clearances and higher pressures. Designed with initial radial interference to effect low pressure sealing, at higher pressures the seal is progressively energised thus increasing the sealing force. Rubberised fabric has the advantage of retaining fluid within its surface so reducing both friction and wear. Style CP is produced with radial grooves incorporated into the top of the seal on the pressure side. This innovative design ensures a rapid energisation of the seal without excessive end float and resultant wear.

These range perameters are Maximum simultaneous conditions. Optimum service conditions are affected by temperature, speed, pressure, surface finish and extrusion gaps.

Refer to Appendix 1 section for further information.

NBR Rubber
DIN Hydraulic Fluid Description °C
H Mineral oil without additives 100
H-L Mineral Fluid with anti corrosion and anti ageing additives 100
H-LP Mineral oil as HL plus additives reducing wear, raising load 100
H-LPD Mineral oil as H-LP but with detergents and dispersants 100
H-V Mineral oil as H-LP plus improved viscosity temp. 100
HFA E Emulsions of mineral oil in water. Water content 80-95% 55
HFA S Synthetic oil in water. Water content 80-95% 55
HFB Emulsions of water in mineral oil. Water content 40% 60
HFC Aqueous polymer solutions. Water content 35% 60
HFD R Phosphoric acid ester based NS
HFD S Chlorinated hydrocarbon based NS
HFD T Mixtures of HFD R and HFD S NS
HEPG Polyglycol based NS
HETG Vegetable Oil based 60
HEES Fully synthetic ester based NS

Maximum Diametral Clearance F:

Note: Clearance gap F is the maximum permissable. i.e. gap completely on one side, in the temperature range of -30°C to 100°C The use of a suitably selected Claron bearing ring will effectively reduce the clearance gap F max. to a value closer to F/2 thus increasing the pressure capability of the seal.

Housing:

For surface finish and recommended lead in chamfers refer to the illustration below. For housing dimensions and machining tolerances refer to the catalogue page of selected seal. Refer to Appendix 4 for value of tolerance symbols.

Fitting:

For the seal to function correctly, it is important that care be taken in fitting the seal within its housing. For a detailed checklist, refer to Appendix 3.

Js 11 f8 H9 +0,25 Nominal Min Max
0,00
ØD1 d1 ØG L1 S C R1
CPI 094063 24,00 16,00 6,30 4,00 2,00 0,20
CPI 106078 27,00 20,00 6,40 3,50 2,00 0,20
CPI 110070 28,00 18,00 6,30 5,00 2,00 0,20
CPI 110078 28,00 20,00 7,00 4,00 2,00 0,20
CPI 118086 30,00 22,00 7,00 4,00 2,00 0,20
CPI 129098 33,00 25,00 7,00 4,00 2,00 0,20
CPI 129098/1 33,00 25,00 6,30 4,00 2,00 0,20
CPI 129098/2 33,00 25,00 7,50 4,00 2,00 0,20
CPI 137098 35,00 25,00 8,00 5,00 2,50 0,40
CPI 149110 38,00 28,00 8,50 5,00 2,50 0,40
CPI 149110/1 38,00 28,00 8,00 5,00 2,50 0,40
CPI 149118 38,00 30,00 6,40 4,00 2,00 0,20
CPI 157110 40,00 28,00 9,00 6,00 3,00 0,40
CPI 157118 40,00 30,00 7,50 5,00 2,50 0,40
CPI 157125 40,00 32,00 9,00 4,00 2,00 0,20
CPI 157125/2 40,00 32,00 8,50 4,00 2,00 0,20
CPI 165125 42,00 32,00 8,00 5,00 2,50 0,40
CPI 169141 43,00 36,00 6,40 3,50 2,00 0,20
CPI 173125 44,00 32,00 12,00 6,00 3,00 0,40
CPI 177118 45,00 30,00 9,50 7,50 4,00 0,80
CPI 177137 45,00 35,00 7,00 5,00 2,50 0,40
CPI 177137/3 45,00 35,00 10,50 5,00 2,50 0,40
CPI 181141/1 46,00 36,00 8,00 5,00 2,50 0,40
CPI 196137/2 50,00 35,00 11,00 7,50 4,00 0,80
CPI 196157/1 50,00 40,00 10,50 5,00 2,50 0,40
CPI 196157/2 50,00 40,00 13,50 5,00 2,50 0,40
CPI 196157/3 50,00 40,00 8,00 5,00 2,50 0,40
CPI 216157 55,00 40,00 8,00 7,50 4,00 0,80
CPI 216157/1 55,00 40,00 10,50 7,50 4,00 0,80
CPI 216177 55,00 45,00 8,00 5,00 2,50 0,40
CPI 216177/1 55,00 45,00 11,00 5,00 2,50 0,40
CPI 236188/1 60,00 48,00 11,00 6,00 3,00 0,40
CPI 236196 60,00 50,00 8,00 5,00 2,50 0,40
CPI 236196/1 60,00 50,00 10,50 5,00 2,50 0,40
CPI 236196/3 60,00 50,00 14,50 5,00 2,50 0,40
CPI 244196/1 62,00 50,00 9,50 6,00 3,00 0,40
CPI 255196 65,00 50,00 11,00 7,50 4,00 0,80
CPI 255216 65,00 55,00 10,50 5,00 2,50 0,40
CPI 259220 66,00 56,00 10,50 5,00 2,50 0,40
CPI 275216 70,00 55,00 10,50 7,50 4,00 0,80
CPI 275236 70,00 60,00 13,00 5,00 2,50 0,40
CPI 275236/3 70,00 60,00 8,00 5,00 2,50 0,40
CPI 279220 71,00 56,00 12,50 7,50 4,00 0,80
CPI 295236 75,00 60,00 13,00 7,50 4,00 0,80
CPI 307248 78,00 63,00 12,50 7,50 4,00 0,80
CPI 314236 80,00 60,00 14,50 10,00 5,00 0,80
CPI 314275 80,00 70,00 12,50 5,00 2,50 0,40
CPI 322275 82,00 70,00 10,50 6,00 3,00 0,40
CPI 326248 83,00 63,00 14,50 10,00 5,00 0,80
CPI 334255 85,00 65,00 14,50 10,00 5,00 0,80
CPI 334275 85,00 70,00 12,50 7,50 4,00 0,80
CPI 354275 90,00 70,00 14,50 10,00 5,00 0,80
CPI 374295 95,00 75,00 14,50 10,00 5,00 0,80
CPI 374314 95,00 80,00 13,00 7,50 4,00 0,80
CPI 374314/1 95,00 80,00 12,50 7,50 4,00 0,80
CPI 393314 100,00 80,00 14,50 10,00 5,00 0,80
CPI 413354/1 105,00 90,00 12,50 7,50 4,00 0,80
CPI 433354 110,00 90,00 12,50 10,00 5,00 0,80
CPI 452374 115,00 95,00 14,50 10,00 5,00 0,80
CPI 452413 115,00 105,00 10,50 5,00 2,50 0,40
CPI 472393 120,00 100,00 14,50 10,00 5,00 0,80
CPI 511433 130,00 110,00 12,50 10,00 5,00 0,80
CPI 551492/1 140,00 125,00 13,00 7,50 4,00 0,80
CPI 629551 160,00 140,00 12,50 10,00 5,00 0,80
CPI 669590/1 170,00 150,00 14,50 10,00 6,00 0,80

Merk

Claron Polyseals

Beoordelingen

Er zijn nog geen beoordelingen.

Wees de eerste om “Claron Polyseal Single Acting Rod Seal CPI” te beoordelen

Het e-mailadres wordt niet gepubliceerd. Vereiste velden zijn gemarkeerd met *

WE’D LOVE TO HELP

Get a qoute